tried it on another pc with the same results....now back on 1.1.1 and synch works again

Sent you the stack trace. The error is just in stdout on the terminal, and the mixingstation app launches in a separate window. The interface just looks very unusable (Separate email with screenshots of windowed/fullscreen)

Does the error prevent the app from starting? Or is it just in the stdout/err?
You can send me the stacktrace via mail if you want ([email protected]).

Also attempted to run with older version of JDK (version 8.0), still no dice and the same error cropped up.

Attempts to modify the config DSON file and use an infintesimal scale (0.01) were unsuccessful. Modified the config file in my $HOME/mixing-station directory

Forgot the size...Display is 1920x1080 at 22"

David, thanks for such a quick reply. The display is 1920x1080, attached to an external monitor. Also tried with VNC session, forced 1920x1080 resolution

Following error appears 3 times in the command window when launching the .jar

What resolution and size is the display?
The app uses the scale reported by the OS and apples its own scaling setting on top of that.
As an alternative you could modify the config file with a text editor and use an even smaller scaling

This is already possible for the decay values. I'll add tap support for the pre delay as well

Sounds good.

It requires a bit of architecture rework internally for which I need a couple of uninterrupted hours to think about.

Hi David,

Hi David, Yes, I see the green line does respect the inactive High Cut.

So on the mixer hicut is disabled but still showing in mixing station?
Then that's by design as otherwise you wouldn't be able to turn it back on again from the app.

Hi David, We shave the 6 PEQ + Low Cut, but there is no High Cut. In the Mixing Station App is shows the High Cut circle and color shading, but when you tap it, it says disables, but it is still visible.

I'm not sure I understand the issue. The mixer has 6 peq bands + Low/Highcut so 8 in total. Or how did you configure the wing?

I have an image, but cannot see how to attach to this ticket. Happy to supply image on request.

OK - even if record, stop and play could be added (a mirror of the multi transport part of the user control section of the Wing would be even better) that would be super handy - We're just implementing the WIng and there's a big learning curve for most people, so it would be good if I could start it recording while in the band at the start of a practice and add markers for each song until I can get everyone trained to the level to do this on the Wing itself. I saw that it's possible to start recording and to add markers over MIDI so it might be possible?
Thanks!

I'd like the option to change the meterbridge to reflect the layers that have been set up - using a Wing, and only using about half the input channels, 1/4 of the DCAs but all the busses. The matrixes are being used for system processing which I don't want to be accessible from the iPad nominally. I've set up layers in a way that I think is logical (and reflects where things are on the layers on the Wing itself). It would be neat if the meterbridge could be changed to only show the meters for the layers that are set up, and the groupings ti reflect the layers (rather than being in 8s) so that pressing the meters can be used to essentially select the layers

The same limitation still applies. Play/Pause might work but no file management

I saw recently that it can be controlled VIA MIDI - is it still not possible to add this to mixing station?

This is already available. You need to enable "Metering window" in the app settings

No, this functionality is not accessible via network

Is it a possibility that this could be added to Mixing Station?

I download and reinstall thé Last xair pro on amazone ( 1.2. 1 (182)) yesterday

Is the old pro version still installed?

Hello, thank for answer but,
I download New app on amazone store, and when i start It, I dont show thé step 4 ( you will be shown à list .....)
Regards
Olivier

See https://dev-core.org/ms-docs/platforms/android/#migration